Diagnostic guide
OBD2 fault codes: what they mean and what to do
You have read a code with an OBD2 reader or another garage gave it to you and you want to know what it really means. Here is the ASF Motors guide: how codes are read, the most frequent ones with their real causes in the workshop, and specific pages for the brands we see most in Zaragoza.
01
How is an OBD2 fault code read?
An OBD2 code has five characters: a letter indicating the system (P powertrain, B body, C chassis, U network), a digit indicating generic (0) or manufacturer-specific (1, 2, 3), and three characters identifying the circuit and fault type; the code says which circuit detected an abnormal value, not which part to replace.
What confuses most is thinking the code names the part. A P0335 says "crankshaft sensor circuit", and the cause may be the sensor, its wiring, an earth or the reluctor ring. That is why at ASF Motors the code is the starting point of diagnosis, not the end. And that is why this guide gives usual causes in the plural.
02
What do I do when the engine warning light comes on?
If the light is steady and the car behaves normally, you can drive for a few days and read the code soon; if it flashes, it indicates misfires that destroy the catalytic converter and you must stop; if the car enters limp mode (reduced power), do not push it and go to the workshop.
Do not clear the code before a garage reads it: with it you lose the "freeze frame", the temperature, rpm and load data at the moment of the fault, which is the best clue. If you have used a reader, note the code and data and bring them. A pocket reader is useful for deciding whether to carry on home, not for repairing.
The most frequent generic OBD2 codes in the workshop
Codes we see every week at ASF Motors, with the causes we actually find. The final cause is always confirmed by measuring.
| Code | Meaning | Usual cause |
|---|---|---|
P0016 | Crankshaft/camshaft correlation (bank 1, sensor A) | Stretched chain or belt, tensioner, phaser, sensor |
P0087 | Fuel rail pressure too low | High-pressure pump, fuel filter, regulator, injector with excess return |
P0101 | Mass air flow: range/performance | Dirty or faulty MAF, intake leaks, air filter |
P0171 | System too lean (bank 1) | Intake leak, MAF, fuel pressure, lambda sensor |
P0234 | Turbo overboost | Seized variable geometry, actuator, control solenoid |
P0299 | Turbo underboost | Intake/intercooler leaks, variable geometry, stuck-open EGR, blocked DPF |
P0300 | Random misfire | Spark plugs, coils, injectors, compression, intake leak |
P0301–P0306 | Misfire in cylinder 1–6 | Coil or plug on that cylinder, injector, compression |
P0335 | Crankshaft position sensor: circuit | Sensor, wiring, damaged reluctor ring |
P0340 | Camshaft position sensor: circuit | Sensor, wiring, timing synchronisation |
P0401 | EGR flow insufficient | Carbon-blocked EGR, passages, position sensor |
P0402 | EGR flow excessive | EGR stuck open, solenoid |
P0420 | Catalyst efficiency below threshold (bank 1) | Degraded catalyst, rear lambda sensor, exhaust leaks, previous misfires |
P0470–P0473 | Exhaust pressure sensor (DPF) | Differential pressure sensor, blocked or split pipes |
P0500 | Vehicle speed sensor | Sensor, wiring, ABS signal |
P0562 | System voltage low | Battery, alternator, earths, wiring |
P0670–P0680 | Glow plug circuit | Failed glow plug, glow relay/module |
P1xxx | Manufacturer-specific codes | See each brand table; need manufacturer-level equipment |
P2002 | Particulate filter efficiency below threshold | Ash-saturated DPF, incomplete regenerations, differential sensor |
P2015 | Intake manifold runner position sensor | Broken or seized linkage, flap motor (common on VAG) |
P2096/P2097 | Post-catalyst fuel trim too lean/rich | Exhaust leaks, lambda sensor, catalyst |
P2BAC | NOx exceedance (SCR) | AdBlue system: dosing, NOx sensors, SCR catalyst |
P0A80 | Replace hybrid battery pack | Imbalanced or degraded hybrid battery modules |
U0100 | Lost communication with engine ECU | ECU power/earth, CAN bus, connectors |
U0121 | Lost communication with ABS module | ABS module, CAN bus, fuse, connectors |
B0001–B00xx | Body codes (airbag, comfort) | Under-seat connectors, pretensioners, airbag module |
C0035–C0040 | Wheel speed sensor | Sensor, ABS ring, wiring |
Fault codes by brand
FAQ
Frequently asked questions
Can I read fault codes myself?
Yes, with an OBD2 reader connected to the port under the steering wheel. It gives you generic P0xxx codes. Manufacturer-specific codes and those from other modules need workshop equipment.
If I clear the code, is the fault fixed?
No. The light will return when the conditions repeat, and you will have lost the freeze-frame data that helps diagnose.
How much does reading codes cost at ASF Motors?
A basic read is quick and included in diagnosis. A full diagnosis with live data and electrical checks is quoted as time; we tell you by phone.
Does a car pass the ITV with fault codes?
With the engine, airbag, ABS or ESP light on, no: it has been a serious defect since 2018. The cause must be repaired, not just cleared.
Is a code the same across brands?
P0xxx codes are. P1xxx and higher, and B, C and U codes, vary by manufacturer. That is why we have brand pages.
Contact
Got a code and not sure what to do? Tell us
Tell us the model and the symptoms. We will tell you what to check first and give you a written quote before touching anything.
- Opening hoursMonday to Friday · 9:00–13:30 and 15:00–19:00 · Saturday 9:00–13:00
- Emailinfo@asfmotors.es
Last updated: