Known faults by engine

PSA PureTech 1.2 engine: wet timing belt

At ASF Motors we inspect and replace the wet timing belt on PureTech 1.2 engines from Peugeot, Citroën, DS and Opel in Cuarte de Huerva, clean the oil circuit of rubber debris and check the vacuum pump and sump. We know the problem and the manufacturer's updated procedure.

PSA PureTech 1.2: wet timing belt · Zaragoza

01

What is the problem with the PureTech 1.2 timing belt?

The PureTech 1.2 uses a timing belt that runs immersed in oil; with the wrong oil, long intervals or urban use the rubber degrades and frays before the planned interval, and the debris blocks the oil pump strainer, vacuum pump and galleries, with a risk of loss of oil pressure and engine failure.

The fault has become so well known that Stellantis has published inspection procedures and warranty extensions. If your car falls within those conditions, we will tell you so you can claim at the dealer before paying anything. If it does not, we repair it ourselves with the updated procedure, which involves much more than changing the belt.

02

How is the PureTech belt inspected and when should it be replaced?

The belt is inspected by removing the oil filler cap and measuring its width with a gauge, plus checking for rubber debris in the sump and vacuum pump; it is replaced if widened or frayed, or if the car is over six years old or past the mileage revised by the manufacturer, even without symptoms.

The inspection is quick and we recommend it on any PureTech over four years old, especially if used in town. What we see in Zaragoza is that cars run on the correct oil standard with annual changes come through fine; those that have had "generic" oil changes show a widened belt at 60,000 km. It has to be looked at.

03

What does the PureTech belt replacement include at ASF Motors?

It includes the latest-specification timing belt, the tensioner, cleaning of the sump and oil pump strainer, inspection or replacement of the vacuum pump, gaskets, oil to the exact PSA standard, filter and an oil pressure check on completion.

Changing only the belt without cleaning the circuit is leaving the job half done: the old belt's debris stays in the sump and can block the strainer. That is why our procedure includes dropping the sump and cleaning. We also check the vacuum pump valve, the cause of the hard brake pedal on these engines. Done this way, the PureTech is a lively, economical engine that need not give more trouble. We apply the same to the Ford 1.0 EcoBoost, which shares the wet-belt concept.

Comparison

Replace the PureTech belt preventively vs. wait for the interval: which is right?

Quick answer: On the PureTech it is best to inspect from four years and replace as soon as the belt widens or the manufacturer's revised interval is reached, without waiting for the original interval: the belt costs far less than an engine with no oil pressure.

CriterionInspection + preventive replacementWait for the original interval
CostBelt, tensioner, cleaning and oilPossible oil pump, vacuum pump, catalyst or engine
RiskLowHigh: loss of oil pressure
Manufacturer warrantyMay apply: we checkMay be lost if the revised interval was exceeded
WhenOver 4 years or urban useNever advisable on this engine

If you have a PureTech, ask for the inspection. It takes fifteen minutes and can save you an engine.

FAQ

Frequently asked questions

How much does a PureTech 1.2 timing belt replacement cost?

It depends on the model and the state of the oil circuit (whether the vacuum or oil pump must be replaced). After inspection we give you a fixed written quote.

Does my car have a PureTech engine?

The 1.2 three-cylinder petrols from Peugeot, Citroën, DS and Opel from 2014 onwards (82, 110 and 130 hp) are PureTech. Tell us the model and year and we will confirm.

Is there a Stellantis warranty extension for the belt?

Yes, the manufacturer has extended warranty and published campaigns for many models and years. During inspection we tell you whether your car qualifies so you can claim at the dealer.

Which oil does the PureTech take?

Oil to the PSA B71 2290 standard (0W-30) or whatever your handbook specifies. An oil without that standard accelerates belt degradation.

Why is the brake pedal hard on my PureTech?

Usually the vacuum pump blocked by belt debris. It is a sign the timing needs inspecting now.

Contact

No-obligation quote for PSA PureTech 1.2: wet timing belt

Tell us the model and the symptoms. We will tell you what to check first and give you a written quote before touching anything.

Last updated: